Motorcycle Won’t Start After Oil Change? Here’s How to Fix It

✓ TIP FOR SAVINGS: Learn if your motorcycle insurance is too expensive!

Comparing quotes can help you save money.

Enter your zip to get started.

ZIP:

An oil change on a bike is the most essential and most frequent maintenance. Imagine if you have changed your oil but your bike won’t start? This can become quite a bothersome problem that will keep occurring if you don’t know how to properly fix it.

This could be caused by: Your motorcycle isn’t starting due to your bike not being in neutral, a kickstand switch isn’t down, no key is in the motorcycle, a clutch switch is overriding the safety switch, a dead battery, no spark is going to the engine, or no fuel is in the motorcycle.

Oil changes are very important, that’s why oil changes are a regular occurrence for a motorcycle owner. These oil changes are quite common so it is important that you know what might cause your motorcycle to stop starting after a change. This article will discuss the main problems and how to change your motorcycle’s oil.

Why Your Motorcycle Won’t Start After An Oil Change

Simple tasks like changing the oil can make it easy to forget what you’re doing and get lost in the process. It becomes a task that you can do without thinking about 20 times. As you start to change your oil, you are setting yourself up for trouble because you aren’t thinking about what you are doing. You may notice your bike not starting after you have finished.

There are many possible reasons for your symptoms. It is best to look for the simple things. It is possible that you missed the obvious solutions because your attention was on one aspect of the bike. Your bike may be in gear, but it won’t start because it needs to be in neutral. Is the key in? Do you need to trigger either the kickstand, or the clutch switch They may not always be the answer, but it is not difficult to make sure you are looking at all of these items. When you’re trying to start a bicycle right after it is finished, it is easy to overlook the simple things.

Next, ensure that your engine has enough spark, fuel, air and fuel. Your bike will not start if it isn’t getting these three things. You must ensure that air is flowing from your intake to the carburetor. These are just three simple things to look for. You can then check the spark. Start the engine by removing the spark plug cap. It should be easy to determine if there is a spark or not. You will be able see it. If it is neither of those two, it’s likely the fuel. You can also check the fuel petcocks. You must ensure that they are turned in the correct direction. If none of these solutions solve your problem, your battery could be the solution.

How to get your motorcycle started after changing the oil

After a regular oil change, your motorcycle should start exactly the same way as it did before. You will want to be careful and ensure that everything is done correctly. First, ensure that the oil you use is the right kind and amount. Once you’ve done this, you can start the bike.

When you first start your bike, pay attention. You want everything to feel and sound normal. Your low oil pressure warning light may turn on for a few seconds after an oil change. This is due to some air in the system, and it takes a few seconds for everything to be filled with oil.

Pre-filling your oil filter with oil prior to installing it is a great way to reduce low oil pressure. This can sometimes be difficult if the oil filter mounts horizontally. If this is the case then adding some oil to your filter will make it more effective than none. It will be easier to fill the filter if it is vertically mounted, or mostly vertical. This will decrease the amount of air, which will keep the oil pressure high after the first startup.

These tips will help you avoid problems starting during an oil change

The best advice you can give is to simply think while changing your oil. Regardless of how many hundreds or thousands of oil changes that you’ve done, it is still important that you pay attention. You will regret it if you just do the bare minimum. You will avoid making a mistake or forgetting something vital for the health of your bike by focusing on what you are doing.

How to properly change the oil on a motorcycle

Routine maintenance is king. This is something you will do repeatedly throughout your entire life. Oil helps to keep your engine lubricated. This prevents internal parts from rubbing against each other. It also pulls heat from the engine. This oil will eventually start to lose its effectiveness as it is exposed over time to extreme temperatures and pressures. Oil that has been used to lubricate and protect the engine is less effective as it degrades.

This is why oil should be changed frequently. This ensures that you have always got fresh oil in your engine. It is not what you want to do to a perfectly good engine. It is so important to keep your oil changed in a timely manner.

How do you change your oil correctly? You will first need to warm up your bike. It will likely be fine if you’ve ridden it in a while. You can start it up if it’s been sitting for a while and let it run for a couple of minutes. THe warms the oil and makes it flow more easily. This will make the process of draining oil painless.

Next, remove the oil cap from the top of your engine. This will allow air through the engine to drain the oil. This will make it easier for the oil to flow. You will then need a socket tool to remove the drain bolt. The oil will seep out as soon as the bolt is removed. Be sure to have something to capture the oil.

It is also important to change the oil filter. Find the oil filter on your bike. It should be possible to grasp the filter and pull it off. Special oil filter wrenches can be used to assist you in gripping and torqueing the filter if you are unable to do so with your hands.. Once the filter has been removed from the bike, it can be re-threaded. This filter also contains oil.

After you let the oil drain, it is time to put everything back together. To prevent any oil from escaping, you will need to put the drain bolt back into place. Now, you can install the new oil filter. You will first need to take some oil and rub it on the O-ring of the oil filter. This will seal the oil filter better. Next, you’ll need to fill up the oil filter with oil. Then, re-install the oil filter on the bike.

Finally, make sure to add enough oil to the bike. Once the oil is refilled, you can turn on the bike. Once everything looks good, you’re done. To make sure you don’t add oil, you will want to monitor your oil levels for the next day.

Leave a Comment